Although I encourage everyone to fill out my list
of needs, here are some basic packages which should help you decide what
you want.
Updated August 15th, 2008.
All packages are listed without motor, add a motor for $106.40 to any package
below:
+1021A $106.40 Motor, 1/4Hp, Pre-wired with switch, switchbox and cord. No
discount
Substitute the assembled lathe (L1017) for the kit version (K1019) for: + $28.89 ($32.10, less 10%)
| K1019 |
$159.40
|
Unassembled Micro Lathe II kit, headstock pre-assembled,
no machining necessary (Pulleys and tailstock not included) 15" bed.
|
| 1022 | $5.25 | Motor mount bracket with necessary hardware, fits above motor and nema 48 frame motors |
| 1023 | $7.70 | Mounting board 12" x 18" used for No. 1021W motor (motor mount bracket not included) recommended, use 3M 500 belt |
| 1030 | $64.75 | 4 jaw 3 1/4" dia. chuck 3/4-16 thd mount jaws adjusted independently (reversable heat treated steel jaws) |
| 1092 | $10.80 | 1/16-3/8" Jacobs drill chuck, commercial quality 3/8-24 thd. |
| 1097B | $5.30 | Right hand tool bit |
| 1150 | $39.50 | Drilling tailstock, lever operated 5/8" off set with dead center, 3/8-24 thd for drill chucks |
| 1162 | $25.80 | Pulley set as above for 1/2" shaft motor 3M 500 20" |
Total $318.50, less 10% $286.65 plus shipping $15.00, $301.65
| K1019 |
$159.40
|
Unassembled Micro Lathe II kit, headstock pre-assembled,
no machining necessary (Pulleys and tailstock not included) 15" bed.
|
| 1022 | $5.25 | Motor mount bracket with necessary hardware, fits above motor and nema 48 frame motors |
| 1023 | $7.70 | Mounting board 12" x 18" used for No. 1021W motor (motor mount bracket not included), use 3M 500 belt |
| 1030 | $64.75 | 4 jaw 3 1/4" dia. chuck 3/4-16 thd mount jaws adjusted independently (reversable heat treated steel jaws) |
| 1035 | $14.90 | Face plate 3 1/4" dia. 3/4-16 thd mount |
| 1040 | $30.80 | Collet set, collet closer with 8 collet sizes 1/8,5/32,3/16,7/32,1/4,9/32,5/16 and one blank |
| 1050 | $64.10 | 3 Jaw 3 1/4" dia. self centering scroll chuck (steel body) with reversable aluminum soft jaws 3/4-16 thd. |
| 1091 | $10.40 | 0-1/4" Jacobs drill chuck, commercial quality 3/8-24 thd. |
| 1093 | $15.70 | 1/8-1/2" Jacobs drill chuck, commercial quality 3/8-24 thd. |
| 1095 | $28.75 | 6 piece high speed steel tool bit set, left,right,45 degree,round nose,boring bar, and cut off |
| 1132 | $2.75 | Blank arbor |
| 1140 | $11.10 | Drill chuck arbor (3/8-24 thread), attaches Jacobs chucks to headstock spindle |
| 1150 | $39.50 | Drilling tailstock, lever operated 5/8" off set with dead center, 3/8-24 thd for drill chucks |
| 1151 | $16.70 | Needle bearing center, spring loaded (fits in tailstock) |
| 1152 | $16.50 | Die holder for tailstock (will accept 13/16" and 1.00" button dies) |
| 1162 | $25.80 | Pulley set as above for 1/2" shaft motor 3M 500 belt 20" |
| 1171 | $5.10 | Back tool post, tool bit mounts upside down, 2 tools may be used at same time |
| 1173 | $31.10 | T Bar Cut off Tool, height adjustable |
| 1190 | $25.30 | Steady rest 3/32" to 1 1/2" capacity |
| 1200 | $44.80 | Top slide (compound) mounts on crosslide for cutting tapers and angles |
| 1220 | $62.90 | Milling attachment mounts directly on crosslide (2 x 3 3/4" table) |
| 1230E | $11.75 | 3/16" dia. milling cutter, 2 flute double end 3/16 shank, mounts in 3/16 collet |
| 1310 | $7.50 | 1" Spindle Wrench |
Total $702.55, less 10% $632.29 plus $35.00 shipping, $667.29
| K1019 |
$159.40
|
Unassembled Micro Lathe II kit, headstock pre-assembled,
no machining necessary (Pulleys and tailstock not included) 15" bed.
|
| 1022 | $5.25 | Motor mount bracket with necessary hardware, fits above motor and nema 48 frame motors |
| 1023 | $7.70 | Mounting board 12" x 18" used for No. 1021W motor (motor mount bracket not included) recommended, use 3M 500 belt |
| 1026 | $3.75 | Depth stop for workpiece in chuck |
| 1030 | $64.75 | 4 jaw 3 1/4" dia. chuck 3/4-16 thd mount jaws adjusted independently (reversable heat treated steel jaws) |
| 1034 | $9.75 | Lathe Dog, holds work piece while turning between centers. |
| 1035 | $14.90 | Face plate 3 1/4" dia. 3/4-16 thd mount |
| 1036 | $5.80 | Face plate angle bracket set |
| 1037 | $8.10 | Face plate, 2" dia. 3/4-16 thd mount |
| 1038 | $26.75 | 4 inch swivel joint tool rest (wood turners) |
| 1040 | $30.80 | Collet set, collet closer with 8 collet sizes 1/8,5/32,3/16,7/32,1/4,9/32,5/16 and one blank |
| 1050 | $64.10 | 3 Jaw 3 1/4" dia. self centering scroll chuck (steel body) with reversable aluminum soft jaws 3/4-16 thd. |
| 1051 | $9.00 | Additional blank soft jaw set for 3 jaw chuck |
| 1052 | $7.80 | Full circle soft jaw set for 3 jaw chuck |
| 1091 | $10.40 | 0-1/4" Jacobs drill chuck, commercial quality 3/8-24 thd. |
| 1093 | $15.70 | 1/8-1/2" Jacobs drill chuck, commercial quality 3/8-24 thd. |
| 1095 | $28.75 | 6 piece high speed steel tool bit set, left,right,45 degree,round nose,boring bar, and cut off |
| 1130 | $4.15 | Blank arbor 1.00" dia. screws directly on spindle (may be machined for special jobs) tapped at other end |
| 1132 | $2.75 | Blank arbor |
| 1140 | $11.10 | Drill chuck arbor (3/8-24 thread), attaches Jacobs chucks to headstock spindle |
| 1150 | $39.50 | Drilling tailstock, lever operated 5/8" off set with dead center, 3/8-24 thd for drill chucks |
| 1151 | $16.70 | Needle bearing center, spring loaded (fits in tailstock) |
| 1152 | $16.50 | Die holder for tailstock (will accept 13/16" and 1.00" button dies) |
| 1162 | $25.80 | Pulley set as above for 1/2" shaft motor STD 3M 315 belt included (3M 500 belt optional) |
| 1170 | $4.70 | Extra tool post (same as supplied with lathe) |
| 1171 | $5.10 | Back tool post, tool bit mounts upside down, 2 tools may be used at same time |
| 1173 | $31.10 | T Bar Cut off Tool, height adjustable |
| 1190 | $25.30 | Steady rest 3/32" to 1 1/2" capacity |
| 1200 | $44.80 | Top slide (compound) mounts on crosslide for cutting tapers and angles |
| 1210 | $20.10 | Radius Turner, swings Tool Bit in arc |
| 1220 | $62.90 | Milling attachment mounts directly on crosslide (2 x 3 3/4" table) |
| 1221 | $14.60 | 3/4-16 chuck adapter, adapts chuck to mill table |
| 1224 | $20.00 | Fly Cutter, 1 1/4 to 2 1/2 inch diameter, 3/4-16 thread mount, tool bit included. |
| 1225 | $27.80 | Milling vice, 2.125" opening x 2" wide |
| 1230 | $50.60 | 5 Piece end mill set (double ended) 1/16,3/32,1/8,5/32,3/16 |
| 1250 | $25.40 | Riser block kit for headstock and tool post (provides 6.00 swing tailstock riser not incl) |
| 1251 | $21.10 | Tailstock riser only |
| 1310 | $7.50 | 1" Spindle Wrench |
Total: $950.20, less 10% $855.18 plus $35.00 shipping $890.18
Here is an accessory package for the ER spindle milling machines.
|
1040ER
|
$56.00
|
ER Collet Set with six ER collets (1/16, 1/8, 3/16, 1/4,
5/16, 3/8)
|
| 1091 |
$10.40
|
0-1/4" Jacobs drill chuck, commercial quality 3/8-24 thd. |
| 1140ER |
$11.10
|
Drill chuck arbor (3/8-24 thread), attaches Jacobs chucks to headstock spindle |
| 2225M |
$31.75
|
Milling vice with handcrank, 2.125" opening x 2" wide (for milling machine only, not lathe milling attachment) |
| 1230 |
$50.00
|
5 Piece end mill set (double ended) 1/16,3/32,1/8,5/32,3/16 |
| 1310 |
$15.00
|
1" Spindle Wrench x 2 (you need two to open and close the collets) |
Total $174.25, less 10% $156.82 plus S&H depending on what else you buy.
Use the package below if you bought the mill with the collets/closer/vise "VC-ER"option:
| 1091 | $10.40 | 0-1/4" Jacobs drill chuck, commercial quality 3/8-24 thd. |
| 1140ER | $11.10 | Drill chuck arbor (3/8-24 thread), attaches Jacobs chucks to headstock spindle |
| 1230 | $50.00 | 5 Piece end mill set (double ended) 1/16,3/32,1/8,5/32,3/16 |
| 1310 | $15.00 | 1" Spindle Wrench x 2 (you need two to open and close the collets) |
Total $86.50, less 10% $77.85 plus S&H depending on what else you buy.
Taig has a few more ER16 accessories available, as well as a tooling plate, here is the "everything" package.
|
1040ER
|
$56.00
|
ER Collet Set with six ER collets (1/16, 1/8, 3/16, 1/4,
5/16, 3/8)
|
| 1091 |
$10.40
|
0-1/4" Jacobs drill chuck, commercial quality 3/8-24 thd. |
| 1140ER |
$11.10
|
Drill chuck arbor (3/8-24 thread), attaches Jacobs chucks to headstock spindle |
| 1110ER | $5.75 | Slitting saw arbor |
| 1224ER | $20.00 | Fly Cutter |
| 2225M |
$31.75
|
Milling vice with handcrank, 2.125" opening x 2" wide (for milling machine only, not lathe milling attachment) |
| 1230 |
$50.00
|
5 Piece end mill set (double ended) 1/16,3/32,1/8,5/32,3/16 |
| 1310 |
$15.00
|
1" Spindle Wrench x 2 (you need two to open and close the collets) |
| 2010 | $60.00 | 4" x 14" x 5/8" Tooling plate for Mill. |
Total $260.00, less 10% $234.00 plus S&H depending on what else you buy.
This package is used by some tobacco pipemakers for stems and tenoning. While the lathe can be used for bowl work, it is better to have a large wood lathe as well...
| K1019 |
$159.40
|
Unassembled Micro Lathe II kit, headstock pre-assembled,
no machining necessary (Pulleys and tailstock not included) 15" bed.
|
| 1022 | $5.25 | Motor mount bracket with necessary hardware, fits above motor and nema 48 frame motors |
| 1023 | $7.70 | Mounting board 12" x 18" used for No. 1021W motor (motor mount bracket not included) recommended, use 3M 500 belt |
| 1038 | $26.75 | 4 inch swivel joint tool rest (wood turners) |
| 1060 | $72.40 | 4 Jaw 3 1/4" dia. self centering scroll chuck (steel body) with aluminum soft jaws 3/4-16 thd. |
| 1093 | $15.70 | 1/8-1/2" Jacobs drill chuck, commercial quality 3/8-24 thd. |
| 1095 | $28.75 | 6 piece high speed steel tool bit set, left,right,45 degree,round nose,boring bar, and cut off |
| 1140 | $11.10 | Drill chuck arbor (3/8-24 thread), attaches Jacobs chucks to headstock spindle |
| 1150 | $39.50 | Drilling tailstock, lever operated 5/8" off set with dead center, 3/8-24 thd for drill chucks |
| 1151 | $16.70 | Needle bearing center, spring loaded (fits in tailstock) |
| 1162 | $25.80 | Pulley set as above for 1/2" shaft motor STD 3M 315 belt included (3M 500 belt optional) |
| 1250 | $25.40 | Riser block kit for headstock and tool post (provides 6.00 swing tailstock riser not incl) |
| 1251 | $21.10 | Tailstock riser only |
Total $455.55, less 10% and $20.00 S&H $429.99